How to Set up a Tub: Install an Acrylic Bathtub as Well as Tub Surround
How to Set up a Tub: Install an Acrylic Bathtub as Well as Tub Surround
Blog Article
Are you trying to locate guidance concerning Tools You Need to Install a New Bathtub ?
Setting up a bath tub isn't precisely rocket science, however it does require solid plumbing, woodworking, and occasionally, tiling skills. Changing an old bath tub with a new one is additionally a reasonably tough task. If the old tub is conveniently accessible, the job can move easily; if you have to open up a wall surface to get rid of the old tub as well as place the new tub, the job is a lot harder. In either case, the project is within a home handyman's skills, although you will certainly need an assistant to move out the old tub and also set in the brand-new one. See to it you have certified on your own for the job as well as fit attempting it. As opposed to working with a contractor to take over a halfway-completed task, it is better to think about utilizing one prior to you begin. Possibilities are you might require a professional plumber to make tube connections.
This post will certainly help you set up a brand-new bath tub in your restroom if you have already acquired a new tub as well as do not require to change the arrangement of your previous water supply pipes.
Your devices and also product list should make up the following:
Preparing for the Setup
To start with, the sustaining structure provided with the bathroom should be fitted (if required) according to the manufacturer's instructions. Next, fit the taps or mixer to the bathtub. When fitting the tap block, it is very important to make certain that if the faucet features a plastic washing machine, it is fitted in between the bathroom and also the faucets. On a plastic bathroom, it is additionally reasonable to fit a supporting plate under the taps unit to prevent strain on the bathtub.
Fit the flexible tap connectors to the bottom of the two taps using 2 nuts and olives (occasionally provided with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet opening, and then pass the outlet through the hole in the bath. Use the nut provided by the supplier to fit the plug-hole. Take a look at the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next off, fit completion of the flexible overflow pipe to the overflow electrical outlet. Afterwards, screw the pipeline to the overflow face which must be fitted inside the bathroom. Ensure you utilize all of the supplied washing machines.
Attach the catch to the bottom of the waste outlet on the bathtub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the trap to the outlet. Connect all-time low of the overflow tube in a similar manner.The bath need to currently prepare to be fitted in its final placement.
Removing Old Touches
If you require to replace old taps with brand-new ones as a part of your setup, then the first thing you should do is separate the water. After doing so, switch on the taps to drain any kind of water staying in the system. The process of getting rid of the existing taps can be quite bothersome due to the limited gain access to that is typically the case.
Make use of a basin wrench (crowsfoot spanner) or a faucet tool to undo the nut that attaches the supply pipes to the taps. Have a towel prepared for the remaining water that will certainly come from the pipelines. When the supply pipes have actually been eliminated, make use of the exact same tool to loosen up the nut that holds the taps onto the bath/basin. You will certainly require to stop the single faucets from turning throughout this procedure. When the taps have actually been removed, the holes in the bath/basin will certainly have to be cleansed of any type of old sealing substance.
Before going on to fit the new faucets, compare the pipeline connections on the old faucets to the new taps. If the old faucets are longer than the new faucets, then a shank adapter is needed for the new faucets to fit.
Setting up the Tub
Using both wood boards under its feet, put the bath tub in the needed placement. The wooden boards are handy in uniformly spreading out the weight of the tub over the location of the boards instead of concentrating all the weight onto four little factors.
The following goal is to make sure that the bathtub is leveled all round. This can be accomplished by checking the spirit level and also adjusting the feet on the bath tub up until the level reviews level.
To set up taps, fit the bottom of the outermost flexible tap port to the ideal supply pipe by making a compression sign up with; after that do the same for the various other faucet.
Switch on the water supply as well as examine all joints and new pipework for leakages and tighten them if required. Load the bath tub and also inspect the overflow electrical outlet and also the normal outlet for leakages.
Ultimately, repair the bath paneling as explained in the supplier's instruction manual. Tiling as well as securing around the tub must wait till the bathtub has been utilized at the very least once as this will certainly resolve it into its final placement.
Suitable New Touches
If the tails of the new taps are plastic, after that you will certainly need a plastic port to stop damage to the thread. One end of the port fits on the plastic tail of the faucet and the other end gives a connection to the existent supply pipelines.
If you require to fit a monobloc, after that you will certainly require decreasing couplers, which links the 10mm pipeline of the monobloc to the standard 15mm supply pipe.
Next, position the tap in the installing opening in the bath/basin ensuring that the washers are in location in between the faucet and the sink. Protect the tap in position with the manufacturer provided backnut. When the faucet is safely in position, the supply pipelines can be connected to the tails of the taps. The taps can either be linked by utilizing corrugated copper piping or with regular faucet adapters. The former type should be connected to the tap ends first, tightening up just by hand. The supply pipelines can later on be attached to the various other end. Tighten up both ends with a spanner after both ends have actually been attached.
Tiling Around the Bath tub
In the location where the bathroom fulfills the tile, it is needed to seal the joins with a silicone rubber caulking. This is very important as the installation can relocate sufficient to split a stiff seal, triggering the water to permeate the wall in between the bathroom as well as the tiling, resulting in problems with dampness and also feasible leakages to the ceiling below.
You can choose from a selection of coloured sealers to blend in your fixtures and installations. They are offered in tubes and also cartridges, as well as are capable of sealing voids approximately a width of 3mm (1/8 inch). If you have a larger void to fill up, you can fill it with spins of soaked newspaper or soft rope. Bear in mind to constantly fill the bathtub with water prior to sealing, to allow for the activity experienced when the tub is in usage. The sealant can crack relatively early if you do not take into account this activity before securing.
Conversely, ceramic coving or quadrant ceramic tiles can be used to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as cut to size, are likewise easily readily available on the marketplace. It is a good idea to fit the tiles using waterproof or water resistant adhesive and also grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
Do you appreciate more info about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround? Place feedback further down. We'd be delighted to see your feelings about this piece. In hopes that you visit us again soon. Enjoyed reading our blog posting? Please share it. Help another person find it. Many thanks for taking the time to read it.
Schedule Your Service
Report this page